Leica Disto X3 Laser Measurer Leica Disto

X3 Laser Measurer Laser Measuring Solution

Leica Disto X3 Video

CONSTRUCTION SITE PROOF

The Leica DISTO^TM  X3 is perfect for tough construction site conditions. It is drop-tested up to 2 m in height, water jet and dust protected to IP 65 standards.

SMART ROOM

New Leica DISTO^TM technologies in combination with the Smart Room function of the Leica DISTO^TM Plan app allow you to quickly create scaled floor plans on your smartphone or tablet.

POINT TO POINT MEASUREMENT

The Leica DST 360 transforms your hand-held laser device into a measurement station. It allows you to measure distances between any two points from one position.

INTUITIVE

Easy to use buttons and functions make working with the DISTO^TM X3 fast and intuitive.

YOUR DISTO X3

The DISTO X3 is designed to make indoor laser measurements an easy task. A holster, hand loop and batteries are included.

 

Specifications

Typ. distance measuring accuracy (ISO 16331-1 certified)	± 1.0 mm
Range (ISO 16331-1 certified)	0.05 up to 150 m
Measuring units	m, ft, in
X-Range Power Technology	Yes
Tilt sensor	Yes
Tilt sensor accuracy to the housing	± 0.2°
Smart Base measuring range Horizontal Vertical	360° for use with Leica DST 360 -64° to > 90° for use with Leica DST 360
Typ. tolerance of P2P function for use with Leica DST 360	± 2mm at 2m, 5mm at 5m, 10mm at 10m
Levelling range	5° for use with Leica DST 360
Memory of last measurement	20
Free software for Windows	Yes
Free App for iOS and Android	Yes
Smart Room function support	Yes
General data interface	Bluetooth® Smart
Data interface for 3D point data	Bluetooth® Smart
Measurements per set of batteries	up to 4’000 (reduced when used with Bluetooth®)
Service life of batteries	up to 8h (reduced when used with Bluetooth®)
Multifunctional endpiece with automatic reference detection	Yes
Batteries	2x AA Alkaline
Protection class	IP 65
2m drop tested	Yes
Dimensions	132 x 56 x 29 mm
Weight with batteries	184g

 

Download Brochure

 

Error 156: The transverse tilt is greater than +/- 10°
To resolve: Hold the instrument without any transverse tilt

---

Error 162: Calibration mistake
To resolve: Make sure the device is placed on an absolutely horizontal and flat surface. Repeat the calibration procedure. If the message still occurs, contact the dealer 

---

Error 204: Calculation error
To resolve: Repeat measurements, make sure to follow the sequence according to the manual

---

Error 205: S910 memory full
To resolve: Delete memory

---

Error 220 & 224: Hardware error
To resolve: If the message continuously appears, contact the dealer for service

---

Error 240 & 245: Data transfer error
To resolve: Re-connect device with computer and repeat procedure

---

Error 252: Temperature too high
To resolve: Let device cool down

---

Error 253: Temperature too low
To resolve: Let device warm up

---

Error 254: Battery voltage too low for measurements
To resolve: Change batteries

---

Error 255: Received signal too weak, measuring time too long
To resolve: Change target surface (i.e. white paper)

---

Error 256: Received signal too high
To resolve: Change target surface (i.e. white paper)

---

Error 257: Too much background light
To resolve: Shadow target area

---

Error 258: Measuring outside of measuring range
To resolve: Correct range

---

Error 260: Laser beam interrupt
To resolve: Repeat measurement

---

Error 284: Laser defect
To resolve: If message continuously appears, contact the dealer for service

---

Error 288-294: Hardware error
To resolve: If message continuously appears, contact the dealer for service

---

Error 300: Smart base not folded out
To resolve: Fold out Smart Base

---

Error 301: Device was moved, levelling not valid anymore
To resolve: Perform levelling again. Levelling with invalid levelling is possible, but it will affect the accuracy

---

Error 302: S910 “Point data transmission” is selected, but WLAN is off
To resolve: Switch on WLAN

---

Error 303 – 306: Error with Leica DST 360 Adapter
To resolve: Repeat procedure and if message still occurs, contact your dealer

---

Error 340: WLAN: Data transfer error
To resolve: Repeat procedure

---

Error 341: Authentication error
To resolve: Use correct password

---

Error >1000: Hardware error
To resolve: If message continuously appears, contact the dealer for service

---

Error 14041: Smart Base defect
To resolve: If message continuously appears, contact the dealer for service